Bed Mats: New! XLT BedMat

Buy Now Find your make/model/year
Product Detail Page - This BedRug XLT Mat is designed specifically for trucks that have an existing spray-in liner or no bed liner. The all new design has an integrated tailgate gap guard hinge that connects the bed piece to the tailgate piece. The polypropylene top layer construction offers a flat work surface, that is slip and skid resistant. The ¾” padded under layer provide dent and impact resistance while offering cushion for your knees while crawling around in your truck bed. The XLT Mat install in minutes using hook and loop fasteners to install without the need to prep, sand or drill holes into your truck bed.

The XLT Mat is made to fit your specific make and model, filling in the ribs and contours of the truck bed to provide a smooth, void free loading surface. The integrated tailgate hinge overs the gap between your truck bed and the tailgate, this will eliminate the annoying build-up of debris between the two pieces. This mat will protect your truck while standing up to whatever you can throw at it: from mulch to bleach. The XLT Mat’s polypropylene material is fade and UV resistant. The ¾" thick foam is similar to that used in life jackets and will not absorb water, resisting mold and mildew. Water will simply run off the surface, out the factory drain holes in the truck bed and will dry in as little as 20 minutes.

  • Ultra-Tough 100% Polypropylene Product (Essentially Plastic)

  • Slip and Skid Resistant, Flat Surface

  • Custom Fit For Each Truck

  • Superior Comfort – Cushioned and Knee Friendly

  • Bleach, Battery Acid, Oil and Gas Wash Right Off

  • Designed For Exterior Use – Will Not Absorb Water

  • Installs in Minutes with Hook and Loop Fasteners

  • No Truck Bed Damage – No Sanding, Prepping, or Drill Holes Needed

WARNING: IMPROPER INSTALLATION WILL RESULT IN MAT FLYING OUT OF THE TRUCK! FOLLOW INSTRUCTIONS EXACTLY!

  1. Loop fasteners are sewn to the bed mat floor panel. Attach the (2) 36in hook fasteners that have a self-adhesive backing to the loop fasteners on the floor.
  2. Lay the bed mat in the bed of the truck to determine the exact location and fit.
  3. Roll one side of the mat up exposing the floor area where the strip of hook fastener is to be adhered.
  4. If the vehicle has a spray in liner, scuff the areas where the hook fasteners are to be attached using steel wool or sandpaper. This must be done to provide a very rough surface for the adhesive to adhere to.
  5. Using a cloth, soap and water, clean and dry this area thoroughly removing all dirt and debris. With a separate cloth, clean the area again with alcohol. Once the area has been cleaned with alcohol, apply the adhesive promoter to a lint free cloth then apply a thin layer to surfaces that have a spray in liner. THE ADHESIVE PROMOTER IS NOT REQUIRED AND SHOULD NOT BE USED FOR APPLYING HOOK FASTENERS TO PAINTED SHEET METAL. Allow the promoter to dry before adhering hook fasteners. *See adhesive promoter information on the promoter package.
  6. Remove the protective liner exposing the adhesive and lay the bed mat down and FIRMLY rub the fastener down VERY AGGRESSIVELY to assure full engagement of the fastener and the adhesive. NOTE: TRUCK BED SURFACE TEMPERATURE SHOULD BE 68° F OR HIGHER IN ORDER FOR THE HOOK FASTENER TO ACHIEVE MAXIMUM ADHESION. ALSO, NEVER CONTAMINATE THE ADHESIVE BY TOUCHING IT WITH YOUR FINGERS.
  7. Repeat for the opposite side of the bed mat.
  8. Carpeted versions of the tailgate mat have loop fasteners sewn at the top and bottom edges. Attach the 1"x2" hook fasteners to the loop fasteners as shown in the illustration below. For TPO versions, attach hook fasteners directly to the back of the tailgate mat as shown below. You may use more than is shown, if necessary.
  9. Align upper edge of tailgate mat with the tailgate.
  10. Repeat steps 4-6.


Limited Lifetime Warranty

BedRug, Inc., warrants BedRug and VanRug for pickup trucks and vans to be free from defects in materials and workmanship. BedRug bedliners will be warranted for the duration of the vehicle ownership by the original BedRug purchaser. The terms of this warranty may vary from state to state. You may have rights under specific state laws that differ from the terms of this warranty. Proof of purchase will be required for warranty service. Customer modifications and/or improper return packaging of the product may void this warranty. Product should be cleaned before return. For warranty instructions, returns and packaging contact BedRug Inc., Customer Service at 800-462-8435. Labor and shipping are not covered under the terms of this agreement.


+ Write a Review

Write a Review

* REQUIRED