Jeep® Kits: Jeep® BedTred Floor Liner

Buy Now Find your make/model/year
You may also be interested in:
BedRug for Jeep®
1998 to Current JEEP® WRANGLER -- TJ, LJ, JK, JKU (CJ-7 & YJ Tail Gate Mats Only)
This fully custom-molded die cut system provides a rugged spray-in look in minutes without the need of any labor intensive prepping or removal of seat brackets or center console. Sold separately as front and rear kit, individual pieces can be quickly removed and hosed off after a long day on the trail if desired. The BedTred material is 100% waterproof, won't absorb water, and will never stain, stink, mold or mildew; dries quickly and resists all harsh chemicals. The 1/4-inch polypropylene foam kit, with provided heat shields, insulates your interior from road noise and heat.

  • HIGH-END, RUGGED SPRAY-IN LOOK

  • CUSTOM MOLDED FOR A PERFECT FIT

  • EASY TO INSTALL & REMOVE

  • INSULATES FROM NOISE & HEAT

  • 100% WATERPROOF


Jeep® is a Registered Trademark of Chrysler L.L.C.
Sold as a 3-piece front and 4-piece rear, the BedTred liner is engineered to replace your OEM carpet. Each piece is custom molded to the factory specifications of your Jeep floor and installs in approximately 30 minutes with the included with hook and loop fasteners. The non-abrasive fiber backing on the underside is used as the loop and the provided hook fasteners with 3M adhesive backing are positioned using the diagram provided within the installation instructions. Because our liners are cut to your specific model there is no trimming, no messy adhesives and no hassle for a perfect fit every time!

The front 3-piece liner set is cut to fit perfectly around the seat brackets and quickly tucks underneath the center console by simply removing two bolts on the rear cup holders. In addition the front kit includes (2) added heat shields for use around the transmission tunnel/console area for added protection to reflect radiant heat. Heat shields easily install using a self-adhesive backing with release liner and are to be positioned in the same locations as the factory heat shields. A diagram is included within the installation instructions to assist in identifying the correct location. Should you wish to retain your rear seat, safety belts and cargo hooks minor trimming on the rear liner set will be needed. These area are pre-marked on the cargo floor piece and/or wheel wells so you’ll know exactly where to make your cuts. (Please note there is a difference between 97-02 & 03-06 seat brackets so make sure to take care on trimming the correct cut lines.)

3YR Limited Warranty

BedRug Inc. warrants BedRug® and BedTredTM products for Jeep® vehicles for three years from the original date of purchase. Warranty is limited to the original purchaser and is not transferable. Product is warranted to be free from defects in materials and workmanship. The warranty is void if the product has been damaged by accident, unreasonable use, neglect, improper service/installation/removal, modifications, acts of God, normal wear and tear, or other causes not arising out of defective materials or workmanship. Consequential and incidental damages are not covered under this warranty. Warranty does not cover labor, the cost of shipping, or cost of returning the product for warranty service or inspection. The terms of this warranty may vary from state to state. You may have rights under specific state laws that differ from the terms of this warranty. Proof of purchase will be required for warranty service. Product should be cleaned before return. A return authorization number must be obtained prior to returning any product. For warranty instructions, returns, and packaging contact BedRug Inc. Customer Service at 800-462-8435.

Jeep® is a Registered Trademark of Chrysler L.L.C.


+ Write a Review
  • BedTred 99 TJ

    Awesome product! I purchased in September 2013 and don't have a single complaint. I chose the BedTred over a replacement carpet because I prefered the look of a spray in liner. I didn't want dust and dirt settling into a carpet. It's really easy to clean...a quick once over with the shop vac and you're good to go...I've even wiped it down with a damp towel. Highly reccomend. 5 stars!

    Rich DeBellis

    New Milford, CT

Write a Review

* REQUIRED